/ Register

Sound Foundations Is Closing Its Doors.

Discussion in 'General Car Audio Discussions' started by sandt38, Aug 12, 2004.

  1. sandt38

    sandt38 Full Member

    Well, for a few days anyways. I am heading out of town for a bit, and I'll be back Sunday evening or Monday. I just wanted everyone to know, and I am sorry for any inconveniences.

    By the time I get back, the new software should be upgraded and the new site active. There will be some new releases and features as well, so keep an eye out.

    Thanks for your patience,
    Seth A
     
    sandt38, Aug 12, 2004
    #1
  2. PolkMM

    PolkMM Full Member

    maybe when you get back monday my brahmas will be ready to be shipped out :)
    -Cody
     
    PolkMM, Aug 12, 2004
    #2
  3. geolemon

    geolemon Full Member

    Eek, rather jaw-dropping title!
    Maybe you want to tone it down a little.. I thought something happened!
    :ranting:
     
    geolemon, Aug 12, 2004
    #3
  4. fugyaself

    fugyaself Full Member

    You SOB. Change the damn title.
     
    fugyaself, Aug 13, 2004
    #4
  5. objext

    objext Full Member

    Same here...my box is half way done ;)
     
    objext, Aug 13, 2004
    #5
  6. Snausages01

    Snausages01 Full Member

    Yea way to go Seth! :angry: :ban:
     
    Snausages01, Aug 13, 2004
    #6
  7. PolkMM

    PolkMM Full Member

    im waiting to get mine before i start pulling out the saw...
    ill be putting them in my current box...then after taking some dimensions of the sub ill start building
    i wish i had a trunk instead of trying to stuff these things under the backseat of my truck
    -Cody
     
    PolkMM, Aug 13, 2004
    #7
  8. TheSSG

    TheSSG Full Member

    Yeah, I had to wait to complete my box, cause I gotta smack in the T-nuts before it's built. Screws would probalby ok, as it's a Birch box but T-nuts are just fun!
     
    TheSSG, Aug 15, 2004
    #8
  9. objext

    objext Full Member

    Yeah, I definitely use t-nuts when building a box I care about. Otherwise I just end up using some beefy sheetmetal screws ;)

    I threw this box together in a few hours today as an interim box & sub until the brahma comes. Couldn't be bothered to use t-nuts or do any type of specialty joints. Sounds so much better/louder than it did as a ~1 cube sealed, though: click
     
    objext, Aug 15, 2004
    #9
  10. sandt38

    sandt38 Full Member

    Chris,

    If I had known that was all it would take to get you back I would have posted that a month ago :p . Where the hell have you been my friend?
     
    sandt38, Aug 15, 2004
    #10
  11. sandt38

    sandt38 Full Member

    YGPM B)
     
    sandt38, Aug 15, 2004
    #11
  12. Snausages01

    Snausages01 Full Member

    Just been 'busy.' I posted a few days earlier on Steven's post about Jesus and his sub. :lmfao:

    Well I have been spending a lot of time on this:

    [​IMG]

    [​IMG]

    The top is the most recent, but the lights were off because I we redoing the plubing (notice no white tubes like in the second picture).

    The stand an canopy still aren't done. :( Its a 120 gallon reef (4'x2'x2'), but it is still in the 'setup' phase.
     
    Snausages01, Aug 16, 2004
    #12
  13. objext

    objext Full Member

    [​IMG]
    [​IMG]
     
    objext, Aug 16, 2004
    #13
  14. Snausages01

    Snausages01 Full Member

    Thanks! ReefCentral and yahoo are bastards. :)
     
    Snausages01, Aug 16, 2004
    #14